Supplier offers wholesale trail mountain bikes designed specifically for children aged 6 to 12 years, featuring geometry optimized for off‑road handling while maintaining a low standover height for safe mounting and dismounting. Each unit is built to withstand repeated impact loads typical of trail riding, with frame fatigue life tested to exceed 10,000 cycles under ISO 4210‑2 mountain bike standards.
Standard wheel size is 20 inches with ISO 622mm rim diameter, paired with 2.1‑inch wide knobby tires that provide a contact patch of approximately 35 cm² per tire, improving traction on loose soil and gravel. The rim width is 23 mm internal, allowing tire pressures between 20 and 35 psi without risk of pinch flats.
| Parameter | Typical Value |
|---|---|
| Frame Material | 6061‑T6 aluminum alloy, hydroformed |
| Frame Weight (size M) | 1.2 kg |
| Suspension Travel (front) | 80 mm air fork, adjustable rebound |
| Brake Type | Hydraulic disc, 160 mm rotor front, 140 mm rear |
| Gear Range | 1×8 speed, 11‑32 t cassette, 32 t chainring |
| Wheelbase | 950 mm |
| Standover Height | 560 mm (adjustable via seat post) |
| Maximum Rider Weight | 45 kg |

The low standover height combined with a slack head tube angle of 68° provides stable steering at speeds under 15 km/h, while the short chainstay length of 380 mm improves maneuverability on tight switchbacks. These dimensions are derived from ergonomic studies of children’s limb proportions and are adjustable via a telescopic seat post with 50 mm travel.
These bikes are intended for use on graded forest trails, single‑track paths, and light gravel sections where young riders develop handling skills. The geometry promotes a neutral riding posture that reduces wrist fatigue during extended rides, and the component selection balances weight savings with durability to meet the demands of frequent use in rental fleets or school‑based cycling programs.
Frame tubes undergo T6 tempering after extrusion, achieving a minimum yield strength of 275 MPa and an elongation of 12 %. Welds are performed using TIG with filler rod matching the base alloy, followed by post‑weld heat treatment to restore temper in the heat‑affected zone. The fork crown and steerer are machined from 7005 aluminum for increased stiffness, with a tapered 1.5‑inch to 1‑inch steerer tube.
Each bicycle undergoes a three‑stage inspection: dimensional verification of critical joints using a CMM with ±0.05 mm tolerance, functional brake test measuring lever force and rotor temperature rise (< 60 °C after 10 repeated stops), and a dynamic load test simulating 200 km of trail riding on a fatigue rig. Units that pass all criteria receive a unique traceability label before packaging.
Bikes are packed in double‑wall corrugated cartons with interior foam inserts protecting the fork, derailleur, and brake calipers. Each carton measures 140 mm × 200 mm × 80 mm (L × W × H) and weighs approximately 5.5 kg including packaging. Palletized shipments use ISO‑standard pallets with strap securing and corner boards to prevent movement during transit.
Standard production lead time for wholesale orders is 25‑30 working days after receipt of deposit and final approval of artwork. Expedited options are available upon request, subject to factory capacity and material availability.
Yes. The seat tube length and top tube length can be adjusted in 10 mm increments to accommodate rider inseam ranges from 400 mm to 560 mm, which corresponds to ages approximately 5 to 13 years.
To generate a quote we need the desired order quantity, preferred frame size(s), color finish, any optional component upgrades, and the destination port for freight cost calculation.
The standard frame is 6061‑T6 aluminum; optional upgrades include 7005 aluminum for increased tensile strength. Forks are supplied in 6061‑T6 aluminum with air‑spring cartridge; a coil‑spring version is available for budget‑focused orders.
Each bike undergoes dimensional checks, brake performance testing, and a fatigue simulation as described in the quality control section. Inspection reports are available upon request.
Standard packaging uses double‑wall cartons with foam protection. For high‑volume orders, we can provide palletized crates with additional edge protection or custom wooden crates upon request.
Cartons are stacked with corrugated dividers, secured with polyester straps, and corner boards are applied to pallets. Shock‑indicator labels are attached to monitor handling conditions during transit.
Lead time ranges from 25 to 30 working days for standard configurations; custom colors or special components may extend this period by up to 7 days.
© SKYS Bicycle Technology Co., Ltd. All Right Reserved. Sitemap | Privacy Policy