This model is engineered for riders aged 7 to 12 who require a lightweight yet durable platform capable of handling trail impacts while maintaining efficient pedaling dynamics.
The bike features a 13‑inch aluminum frame with a tapered headtube, internal cable routing, and a symmetrical rear triangle designed to accommodate a 100 mm travel air‑spring rear shock.
Wheel size is set at 24 inches with a 30 mm internal rim width, allowing tire widths from 2.0 to 2.4 inches without compromising clearance.
Key dimensions influence handling, rider fit, and stability on descents; the following table lists nominal values for a medium (13″) frame.
| Dimension | Value (mm) |
|---|---|
| Seat Tube Length | 330 |
| Top Tube Length (horizontal) | 540 |
| Head Tube Angle | 68.5° |
| Chainstay Length | 410 |
| Wheelbase | 1020 |
The rear shock utilizes an air‑spring with adjustable preload and rebound, offering 100 mm of travel measured at the rear axle.
A fork with 80 mm travel, tapered steerer, and 32 mm stanchions provides front‑end compliance while keeping weight under 1.8 kg.
Power is transferred via a Shimano Altus 2×8 speed crankset with a 22‑32 T chainring combination and an 11‑32 T cassette, yielding a gear range of approximately 300 %.
Shift actuation uses indexed trigger shifters mounted on the handlebar, enabling precise gear changes under load.
Hydraulic disc brakes feature 160 mm rotors front and rear, with four‑piston calipers delivering consistent modulation in wet conditions.
Brake levers are equipped with reach adjustment to accommodate smaller hand sizes typical of the target age group.
Rims are double‑wall alloy with a 30 mm internal width, compatible with tubeless‑ready tires and featuring a 24‑hole lacing pattern for balanced stiffness.
Standard tires are 24×2.25 in with a directional tread pattern optimized for loose over hard surfaces, providing a rolling resistance coefficient of roughly 0.0045 on packed gravel.
The main frame tubes are constructed from 6061‑T6 aluminum, hydroformed to achieve varying wall thicknesses that optimize strength‑to‑weight ratio.

Joints are welded using TIG process with post‑weld heat treatment to relieve stresses, followed by a powder‑coat finish rated for 500 hours of UV exposure without significant fading.
Each frame undergoes dimensional inspection using a CMM with tolerance ±0.2 mm on critical interfaces such as headtube and bottom bracket shells.
Completed bikes are subjected to a dynamic fatigue test simulating 100,000 pedal cycles at 250 W output to verify long‑term durability of the suspension pivots.
Wholesale distributors stock this model for regional bike shops, school‑based cycling programs, and youth‑focused rental fleets where service intervals and parts availability are critical.
Factory‑direct purchasing enables adjustments to geometry, component spec, and finish without requiring tooling changes.
Bikes are packed in double‑wall corrugated cartons with internal foam protection for the frame, fork, and wheels, achieving a dimensional weight of approximately 18 kg per unit.
Cartons are palletized (48 units per pallet) and secured with stretch film, meeting ISPM‑15 standards for international shipment.
Yes, the frame is offered in 11″, 13″, and 15″ seat‑tube lengths; each size corresponds to a specific reach and stack range to accommodate riders from 110 cm to 150 cm tall.
Buyers should provide desired quantity, preferred component tier (e.g., drivetrain level), any custom color or finish requests, and the destination port for freight calculation.
The standard frame uses 6061‑T6 aluminum; alternative 7005 alloy or scandium‑enhanced aluminum can be quoted for projects requiring higher strength‑to‑weight ratios.
Each bike receives a visual check, torque verification of critical bolts, and a functional test of suspension travel, brake lever feel, and gear indexing.
Units are placed in individual cartons with corner protectors, then stacked on pallets and wrapped with stretch film; additional edge boards can be added for high‑volume shipments.
Lead time ranges from 25 to 35 working days after receipt of deposit and final specifications, depending on current factory load and component availability.
To discuss pricing, lead times, or customization details, please reach out via our inquiry form.
© SKYS Bicycle Technology Co., Ltd. All Right Reserved. Sitemap | Privacy Policy